AWgage-150 Metal Film Metrology
220 Cochrane Circle
Email: sales@allwin21.com
Morgan Hill, CA 95037
Production proven AWgage-150 Metal Thin Film Metrology
sales@allwin21.com
AWgage-150 measures sheet resistance in ohms per square or milliohms per square. If specific resistivity is known, the thickness of the deposited film layer can be computed from the sheet resistance. The choice of measurement data is easily get in the software. AWgage-150 can accommodate 150mm (6") wafers as well as the standard 2", 3",4", 5" wafers without any hardware change
AWgage-150 Metal Thin Film Metrology Key Features:
30 years proven Eddy Sheet Resistance Measurement technology.
Non-contact Sheet Resistance Measurement.
1mW/square to 19,990W/square sheet resistance measurement range.
100Å to 270kÅ Metal Film Thickness range.
Touch Screen Monitor GUI and PC w/ Advanced Allwin21 software.
Wafer carriage travel programmed with internal encoder step motor , without encoder disk.
Consistent wafer-to-wafer process cycle repeatability.
Small footprint and energy efficient.
Made in U.S.A.
AWgage-150 Metal Thin Film Metrology Software Key Features:
The AWgage-150 system is controlled by menu commands from the control software. This software allows a great deal of flexibility and control of the Allwin21 system. The AWgage-150 control software features the following:
Automated calibration of all subsystems from within the control software. This allows faster and easier calibration, leading to enhanced process results. The AWgage-150 allows calibration of the ohm and milliohm measurements within the software for maximum performance and accuracy. This provides a much easier and faster method to calibrate the instrument than by adjusting pots on the back of the traditional Sheet Resistance Measurement Instrument.
The SOFTWARE can compensate for where the flat is on the carriage to locate the test points.
It features a recipe editor to create and edit recipes to fully automate the processing of wafers on the Allwin21 system.
Validation of the recipe so improper points will be revealed.
Storage of multiple recipes, process data and calibration files so that process and calibration results can be maintained and compared over time.
Passwords provide security for the system, recipe editing, diagnostics, calibration and setup functions.
Simple and easy to use menu screens which allow an automatic cycle to be easily defined and executed.
Troubleshooting features which allow engineers and service personnel to activate individual subassemblies and functions.
AWgage-150 Metal Thin Film Metrology Specifications:
Perform odd number of site tests: 1 to 9 points
Highly Conductive or Metal Sheet Resistance:1 to 1,999 mW/square, or 1 to 1,999 W/square, or 10 to 19,990 W/square
Highly Conductive or Metal Film Thickness: Minimum: 100 Ångström; Maximum: Proportional to resistivity. Maximum for a resistivity of 2.7 mW-cm is 270 k Å (27 mm)
Sheet Resistance Repeatability:Total repeatability is the standard deviation (s) percent of mean value(X%),1 count.1 to 100 mW/sq; W/sq 1%;100 to 500 mW/sq; W/sq 2%; 500 to 1000 mW/sq; W/sq 4%; 1000 to 1,999 mW/sq; W/sq 6%’ 1,999 to 5,000 W/sq/ 5000 to 10,000 W/sq / 10,000 to 15,000 W/sq Consult Factory
AWgage-150 Metal Thin Film Metrology Configuration:
Main Frame
Wafer Carriage (2”-6”)
Measurement Head
RF Tank Circuit board
Pentium® class computer board
Main control board
Motor control board.
Two USB Ports
Two Extra DB9 Ports
15–inch touch screen GUI
Allwin21 Corp proprietary software package.
Mouse & keyboard .
USB Flash Drive with AW Software backup.
CE Certification (Optional)
AWgage-150 Metal Thin Film Metrology Measurement Processes:
Turn on the power to the AWgage-150. Allow 30 minutes for warming up.
Select an existing recipe or create a new recipe.
When The carriage is in the loading position, place the wafer on the carriage between the four locator blocks. The wafer will be centered over the circular platform that rotates the wafer.
Manual Mode: Press the MAN/AUTO button, so the LED is off. Momentarily press the START/STANDBY button. The carriage will move the wafer under the measurement head to the first point in the measurement sequence. For multi-point measurements--press START/STANDBY once for each point in the measurement sequence. The wafer will be advanced to the next point. When the measurement sequence is complete the carriage will move to the right until the wafer is out from under the measurement head in the loading/unloading position. The wafer can be removed from the carriage after it has reached this position.
Automatic Mode: Press the MAN/AUTO button on the AWgage-150 control panel until the LED comes on. Press the START/STANDBY button. The entire measurement sequence will be performed without further operator intervention. When the sequence is complete, the wafer will be moved to the unloading position.
PC Screen Mode: Press the “Start Test” button at the Process Screens (for Engineer or Production) to test the wafer that is on the wafer carriage, using the selected recipe. The entire measurement sequence will be performed without further operator intervention. When the sequence is complete, the wafer will be moved to the unloading position.
All data measurements are recorded in the computer for later retrieval, inspection and, if desired, a print-out of the measured points can be printed on an external printer.
AWgage-150 Metal Thin Film Metrology Facilities Requirements:
Instrument needs to be on a hard/solid surface.
The room temperature should be close to 23° C for the greatest measurement accuracy.
Avoid environments with high concentrations of particulates, especially abrasives such as glass and silicon dust.
Power : 50/60Hz, Single Phase, 110/220VAC, 2 Amps
Weight and Dimensions: 44 LBs ; 11 inch (W) X 18 inch (D) X 22 inch (H)
Keywords:Mgage 200, Mgage 300, M-gage 200, M-gage 300,Sheet Resistant measurement, Metrology, Tencor M-Gage 300,Tencor M-Gage 200, sheet resistance, sheet resistance Measurement, Semiconductor Equipment, Semiconductor metrology Equipment, KLA-Tencor, Tencor
Keywords: Mgage 200, Mgage 300, M-gage 200, M-gage 300,Sheet Resistant measurement, Metrology, Tencor M-Gage 300,Tencor M-Gage 200, sheet resistance, sheet resistance Measurement, Semiconductor Equipment, Semiconductor metrology Equipment, KLA-Tencor, Tencor
Customer Reviews for AWgage-150 Metal Film Metrology
Be the first to review AWgage-150 Metal Film Metrology - Use the thumbs to get started!
Click to Rate:
0 thumbs up, 0 thumbs down
Interview Q&A
How long have you been in business?
15 years
What is your primary product or service?
Allwin21 Corp. was formed in 2000 with a focus on professionally providing Rapid Thermal Process, Plasma Asher Strip / Descum, Plasma Etch/RIE, Sputter Deposition and Metal Film Metrology high-tech semiconductor equipment, services and technical support in Semiconductor III-V, MEMS, Biomedical, Nanotechnology, Solar, Battery & LED industries. We endeavor to be a leader in our product lines.
We focus on extending product lifecycle, providing solutions, and engineering enhancements to many production proven semiconductor process equipment most directly related to III-V processing. These semiconductor equipment have been used in production and R&D since the 1990′s. They have proven processes and research. Allwin21 Corp. customizes these systems with Allwin21′s comparable integrated process control system with PC, solid robotic wafer transfer system, and new critical components. This is to achieve the goal of giving our customers a production edge, with right cost, and without having to worry about obsolete parts.
Allwin21 Corp. is the exclusive licensed manufacturer of AG Associates Heatpulse 610 Rapid Thermal Process tool. We are manufacturing the new AccuThermo AW Series Rapid Thermal Processors. Compared with traditional RTP systems, Allwin21’s AccuThermo AW RTPs have innovative software and more advanced real time temperature control technologies to achieve the BEST rapid thermal processing performance (repeatability, uniformity, and stability) with decades of research directly applicable to ours.
We have maintained a global presence that has grown and expanded into the major high-tech manufacturing areas of the world. We pride ourselves on developing and continuing lasting customer relationships.
We understand that a timely responsive support and service are critical elements in semiconductor industries. Allwin21’s experienced engineer team is the best guarantee for high quality service and support. We provide on-site installation, training, maintenance, system optimization, retrofits, and/or customized upgrades
What sets us apart from the competition…
1) Exclusive licensed manufacturer of Heatpulse 610 of AG Associates.
2) Advanced Allwin21 Real Time PC Control Technology.
3) Focus on Production-Proven process technology.
4) Integrated 3-axis solid robotic wafer transfer technology.
5) Experienced local engineer support.
6) Products made in U.S.A
Main Products:
Rapid Thermal Process
AccuThermo AW410
AccuThermo AW610
AccuThermo AW810
AccuThermo AW820
AccuThermo AW610V
AccuThermo AW820V
Sputter Deposition
AccuSputter AW4450
Perkin Elmer 4400
Perkin Elmer 4410
Perkin Elmer 4450
Plasma Ash/Descum
AW-105R
AW-1008
AW-B3000
Plasma Etch/RIE
AW-2001R
AW-901eR
AW-903eR
TTW AW-901eR
TTW AW-903eR
Metal Film Metrology
AWgage-150
AWgage-200
Upgrade Kits for :
AG Associates Heatpulse 210, Minipulse 310, Heatpulse 410, Heatpulse 610 Rapid Thermal Processing equipment; Tegal 901e, Tegal 903e, Gasonics AE 2001, Matrix 303, Matrix 403, Lam AutoEtch 490, Lam AutoEtch 590, Lam AutoEtch 690, Lam AutoEtch 790, Lam AutoEtch 480, Lam AutoEtch 580, Lam AutoEtch 680, Lam AutoEtch 780 Plasma Etcher equipment;Matrix 105, Matrix 106,Matrix 205, Matrix 101,Matrix 102,Matrix 103, Matrix 104, Matrix 10, Gasonics Aura 1000, Gasonics Aura 3000, Gasonics Aura 3010, Gasonics L3510, Branson/IPC 2000, Branson/IPC 3000, Branson/IPC 4000 Plasma Asher ,Plasma Descum Equipment; Perkin-Elmer 4400, Perkin-Elmer 4410, Perkin-Elmer 4450, Perkin-Elmer 4480, Perkin-Elmer 2400 sputter deposition systems
How did you first become interested in your line of business? (if owner) - What is your background? (If owner or store manager)
We have been the process engineer and equipment engineer for more than 20 years.
How do you differentiate yourself from other businesses in your category and area?
1) Exclusive licensed manufacturer of Heatpulse 610 of AG Associates.
2) Advanced Allwin21 Real Time PC Control Technology.
3) Focus on Production-Proven process technology.
4) Integrated 3-axis solid robotic wafer transfer technology.
5) Experienced local engineer support.
How many locations do you have and do you have plans to expand?
All over the world.
Provide detailed directions to your location
220 Cochrane Circle, Morgan Hill,CA95037
What type of payments do you accept?
Cash,Check,remit
What are your hours of operation?
9am-5pm
Contact AWgage-150 Metal Film Metrology:
Problem with this listing? Please report it
